THERMADOR Error Code E8
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E8 | Turns heat off on failed oven only, micro not affected. Error will remain in display until repaired and powered up. No error tones.Turns heat off on failed oven only, micro not affected. | Repair the electronic range control (also called clock or ERC) |
The control continually keeps track of system parameters for control as well as stove failings and reports a fault code when a system trouble is spotted. The control makes use of the ovens blue “on light” and also oven “heating light” to report a detected fault code. The control will certainly remain to flash the lights in the suitable sequence as long as the fault exists.
Discovery of a fault does not hinder the capability of the control to remain to function if the fault is not essential for the intended operation. For instance: If the range door lock is inoperative, the range will certainly continue to cook because the fault would only prevent the range from self-cleaning.
HOW TO TRANSLATE CODES
When a mistake takes place, the control will blink the blue oven “on light” and heaven “heating light” sequentially to indicate the fault. The fault codes have two numbers, these numbers are translated by the number of times the lights flash. The stove “on light” will certainly flash indicating the initial number, as well as the “heating light” will blink indicating the second number.
INSTANCE:
Error E9 is … No Cooling Fans. The code is 43. The stove “on light” will flash 4 times, then the “heating light” will certainly flash 3 times, after that pause. The series will after that duplicate as long as the fault is present.
MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart shows the error codes that can be shown in the Oven/Selector home window throughout particular oven malfunctions. Several of the mistake messages can be cleared by executing the adhering to actions:
- Turn the selector knob to OFF
2.”Fine-tune” the stove by transforming the selector handle slightly to the left (counterclockwise). This might quit the blinking message/beeping as well as clear the window. - For errors E1, E9, E11, E12 and E13, the power supply mosting likely to the also need to be switched off momentarily, and back on once again.
- If a mistake stays presented when the selector switch is OFF, and after trying to clear the display, as displayed in steps 2 as well as 3, shut off the power going to the oven, as well as describe the chart below to aid you locate the trouble.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |